Rainbow-electronics FARGO MAESTRO 100 (with TCP_IP) Instrukcja Użytkownika Strona 150
- Strona / 787
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Serial Port Commands
DCE Response Format V
©Restricted
Page: 144 / 184
This document is the sole and exclusive property of Wavecom. Not to be distributed or divulged without
prior written agreement.
WM_DEV_OAT_UGD_049 - 001 VOLUME 1 August 23, 2007
8.6 DCE Response Format V
8.6.1 Description
This command determines whether the DCE response format uses or not the header
characters <CR><LF>, and whether the result codes are provided as numeric or
verbose.
8.6.2 Syntax
Action command
ATV<n>
OK
Read command
None
Test command
None
8.6.3 Parameters and Defined Values
<n>: format control parameter
information responses result code
0 <text><CR><LF> <numeric code><CR>
1 (default
value)
<CR><LF>
<text><CR><LF>
<CR><LF>
<verbose code><CR><LF>
.
8.6.4 Parameter Storage
The <n> parameter is stored in EEPROM using AT&W command. The default value
can be restored using AT&F.
- AT Commands Interface Guide 1
- Firmware v6.63 1
- Trademarks 3
- Copyright 3
- Overview 4
- Document History 5
- VOLUME 1 8
- ©Restricted 10
- 1 Introduction 11
- Introduction 12
- 1.2 Related Documents 12
- 1.3 ETSI Secretariat 14
- 2 AT Commands Features 21
- AT Commands Features 22
- 2.7 Length of Phone Numbers 23
- 2.8 Bad Software Message 23
- 4 Identifications commands 26
- Note: Request IMEI SVN 40
- Note: Update the IMEI SVN 40
- 5 Open AT 42
- Commands 42
- Com mand Responses 43
- Commands 46
- <err>" 55
- Note: Enable slow idle mode 87
- Note: Disable slow idle mode 87
- Note: Idem 97
- Action command 100
- Read command 100
- Test command 100
- Command Responses 101
- Note: Done 101
- Note: Possible values 108
- Note: Custom character set 108
- Note: Get current value 108
- Note: Get possible values 108
- Unsolicited response 112
- 7 Wireless CPU 119
- Status Commands 119
- Wireless CPU 121
- Status Commands 121
- 8 Serial Port Commands 140
- Note: Enables autobauding 143
- Serial Port Commands 145
- Note: New values 146
- Note: Current values 146
- Note: Get supported values 169
- Note: Enter multiplex mode 169
- Note: Get current values 169
- Note: No OK 170
- Security Commands 171
- Related Documents 192
- Contents 194
- VOLUME 2 194
- GSM Network Commands 200
- Unsollicited response 215
- >: Location Area Code 216
- <CI>: 216
- <NetMeas>: 216
- <BCCHlist>: 217
- <TA>: 217
- <Date and Time>: 217
- Note: <rssi> is 23 221
- Call Control Commands 225
- 12.8 Remote disconnection 239
- Note: Current value 245
- Note: CSD data call 251
- Note: Incoming voice call 253
- 13 Data Commands 254
- Data Commands 256
- Note: Select a bearer 257
- Note: CSD call 260
- Note: Data rate is 9600 260
- Note: Set new parameters 262
- Intermediate response 271
- Note: Reporting enabled 272
- Note: outgoing data call 272
- Note: No error correction 274
- Note: Enter GSM mode 276
- GPRS Commands 279
- Note: Delete <cid>=1 286
- CONNECT 295
- Note: Context 2 is active 325
- PLMN Commands 331
- Contents 350
- VOLUME 3 350
- Phonebooks Commands 353
- Note: ADN phonebook 370
- Note: Test command 396
- Note: Possible services 406
- Short message Commands 410
- OK), but the 412
- Write, send: SMS 420
- Test command1 429
- Note: New message received 439
- SIM Commands 473
- (e.g. for 483
- (SMS, phonebook…) 484
- SIM ToolKit Commands 485
- Note: Select Item 1 506
- Note: End of session 506
- 20.2.4 Parameter Storage 514
- 20.3.4 Parameter Storage 517
- 20.5.2 Syntax 521
- 20.5.1 Description 521
- 20.5.4 Parameter Storage 522
- 20.6.4 Parameter Storage 526
- 20.7.4 Parameter Storage 529
- Note: Sequence not allowed 538
- 20.11.1 Description 539
- 20.11.2 Syntax 539
- VOLUME 4 552
- Note: Activate config1 555
- Audio Commands 556
- Note: Stop DTMF decoding 597
- DTMF Decoding 598
- Note: Selects the buzzer 615
- Action Command 620
- Read Command 620
- I/O Commands 623
- Note: GPIO state is written 631
- Battery Commands 642
- °C mV °C mV °C mV 647
- AT+WDIAG=0,1,5,0,0,0,0 652
- +WDIAGI: 3 654
- +WDIAGI: 4,4300 654
- CPHS Commands 658
- Note: Activate line 1 670
- 25 Fax Commands 671
- V.17 type modem 673
- Fax class 2 Commands 696
- Note: Change bit rate 697
- APPENDIXES 707
- © Restricted 709
- 1 Codes and Values 710
- 1.7 Result Codes 719
- 1.8 GSM Sequences List 719
- 1.9 Operator Names 722
- 1.10 CPHS Information Field 722
- 1.11 CSP Constants 723
- 2 Examples 727
- Command Response 731
- // Wireless CPU 746
- reset is needed 746
- reset is not needed 746
- 3 Technical Appendixes 752
- 3.2 Multiplexing Mode 756
- 000 1001 1 773
- 3.9 USB CDC feature 783
- 4 Interoperability 786
- - New Territories, Hong Kong 787
Powiązane produkty i podręczniki dla Odbiornik GPS Rainbow-electronics FARGO MAESTRO 100 (with TCP_IP)
(9 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji